How to Replace a Kia Sportage Replacement Key

The key of a lot of kia optima key replacement models comes with a keyless entry system built in. The key functions like a remote control, and can be exchanged by a Kia dealer.

Key fobs may stop working due to a number of reasons, such as the battery being dead, worn-out buttons signals, signal interference or water damage. Here are some helpful tips on how to get your kia rio keyless entry Sportage replacement key to work again.

How do you replace a smartkey or remote key?

Whether your Kia comes with an intelligent key, remote key, push-to-start key, or a standard non-transponder key made of metal The battery inside these keys will eventually require replacing. This is especially when your car displays a message telling you that the smart or remote keys are not powered by batteries.

It's a simple procedure. To replace the battery on the keyfob remove the mechanical key from the slit that is located at the back of the fob. Then, you need to pry the cover off. Inside the key fob, there will be a small screw that holds the battery in its place. Remove the old battery by removing the screw with the help of a small screwdriver. Insert the new battery and then close the opening on the key fob.

Test the key fob by pressing the lock and unlock buttons. It's okay If the doors lock and unlock as you expect. You can now take advantage of the Kia's hands-free lock/unlock feature when your fingers start to get cold or you have to run some errands in Brandon.

Note: Some key fobs might need to be programmed (transponder chips or smart keys). This requires a machine for programming that is only available to the locksmith who works for the automotive dealer. Other keys (non-transponder metal keys) do not require programming a kia key fob. If your keys need to be programmed, you must be aware of the key code number stamped on the tag that identifies the key and record the number in a secure place.

how to get a new kia key fob do you replace the battery?

If the Kia key fob doesn't respond to pressing the lock/unlock button, it's likely that the battery is depleted. A battery that is not functioning properly could cause other problems like the check engine light coming on or a delay in cranking the engine. Fortunately, replacing the battery on the key fob is a fairly simple DIY project that requires only a few basic tools.

Before you begin the process, make sure that your vehicle is off and that all doors are shut. Locate the small metal or plastic piece that is on the bottom of your key fob, and play with it until a metallic key slips out. This key can be put into the driver door handle to unlock your car.

To replace the battery in the key fob remove the cover on the rear. Utilize a plastic plier tool to loosen up the latch that holds the black negative cable. Remove the old battery and then place the new battery to ensure that its "+" side is facing you and the "-" negative side is facing the fob's electrical contacts. Avoid using too much force when pushing the new CR2032 into place to avoid damaging or bending the metal contacts.

After the new battery has been installed, turn the key fob off and then turn it on in the ignition several times until the door locks. You can then test your Kia's key fob again to make sure it's functioning properly.

How to replace the smart key?

You could have an ordinary keyfob or Smart Key, based on the model of Kia Sportage. The smart key features an embedded mechanical key blade, unlike the standard key fob, which does not. Both key fobs have an internal battery that will eventually require replacement. Fortunately, it's an easy process that takes just two minutes.

Be sure to switch off your kia sportage key and sit on a level or well-lit surface prior to when you begin. Keep in mind that the fob has small pieces that could fall if you're not careful.

The first step is to locate the small release button on the backside of the fob. This will either be an oval silver button or a rectangular slot. You can open the key fob by pressing the button.

Once you have the key fob open, you can simply take off the old battery and replace it. The new battery is a CR-2032 that can be purchased online or at a local auto parts store. After you've finished, your key fob should allow you to lock, unlock, and start your vehicle even if it's not running.

How To Find A Lost Kia Key Fob do I replace a mechanical key

The Kia keyfob is a wonderful convenience that allows us to lock or unlock our car by simply pressing the button. However, like all devices, it can have problems at times. There are methods to troubleshoot these issues and ensure that our key fobs are in good working condition for the long term.

A dead or weak battery is among the most common problems. The battery could cause the device to stop working or operate intermittently. If this happens try replacing the battery with a fresh new one.

If this does not resolve the issue, you can use the flathead screwdriver that is standard to wedge the fob's plastic casing open. Be careful not to scratch any internal components or scratch the plastic. After the battery has been removed and replaced with a brand new one.

Close and open the door with the mechanical key. (Every kia fob comes with an emergency mechanical key that fits into the slot). Test the key fob to ensure that it's working properly. If the device not working, contact an authorized locksmith or dealer to help solve the problem. To avoid locking outs in the future, ensure you purchase an emergency key that can work in all of the door and trunk cylinders.