How to Replace a kia rio keyless entry Sportage Replacement Key

The key on many Kia models comes with a keyless entry system built into. This key is similar to the remote control, and can be exchanged by an Kia dealer.

Key fobs might stop working due to a variety of reasons, such as a dead battery, worn-out buttons signal interference, or water damage. Here are some suggestions to help you get your kia sportage key fob Programming sportage replacement key to work again.

How to replace the remote key or smart key

If your 2014 kia sportage key fob is equipped with an intelligent key, remote key push to start key or regular metal non-transponder key the battery in these keys will eventually require replacement. This is particularly when the car displays a message telling that the remote or smart key is not powered by the battery.

Luckily, this is an easy process. To replace the key fob battery remove the mechanical key from the hole in the back of the key fob and lift the cover. A small screw will be found inside the key fob to keep the battery in place. Take out the old battery by detaching the screw with the help of a small screwdriver. Install the new battery and close the gap on the key fob.

Once the key fob has new batteries Test it by pressing the lock and unlock buttons. You're good to go when the doors lock or unlock as expected. You can now utilize the hands-free feature to lock and unlock your Kia whenever your fingers become cold or you need to go on errands around Brandon.

Note: Certain key fobs (transponder chip or smart keys) may require their programming completed. This requires a particular programming machine that only the dealer or locksmith can access. Other keys (non transponder keys made of steel) don't require programming. If your key has to be reprogrammed, then you will need to know the key code number written on the tag that identifies the key and save it in a safe location.

How do I replace the battery?

If the Kia key fob does not respond to pressing the lock or unlock button, it is most likely that the battery is not fully charged. A low battery could cause other issues, such as the check engine light turning on or a delay in cranking the engine. Fortunately, replacing the key fob battery is a relatively easy DIY project that requires just a few tools.

Before you begin, make sure that your vehicle is turned off and that all doors are shut. Find the small metal or plastic piece on the bottom of your key fob and jiggle it until a metal key slides out. This key can be put into the door's driver handle to unlock your car.

To replace the key fob's battery, take off the cover at the rear and use a plier bar tool to release the latch holding the black negative battery cable. Take the old battery out, and then orient the replacement battery to ensure that its "+" side faces you, and the "-" negative side is facing the fob's electrical contacts. Avoid using excessive force when pushing the new CR2032 into place to avoid breaking or bending the steel contacts.

After you have installed the new battery then turn the key fob on and off in the ignition until the door locks cycle. Then you can test your Kia key fob to determine if it is working properly again.

How can you replace the smart key?

Depending on the model of the Kia Sportage, you may have a standard key fob or a smart key. The smart key is equipped with an embedded mechanical key blade, however, the standard key fob does not. Both key fobs contain a battery that will eventually require changing. It is a simple process that takes less than two minutes.

Make sure you turn off your kia key copy and stand on a level well-lit and well-lit area before you begin. Also, keep in mind that there are tiny parts inside the fob which could be removed if not vigilant.

The first step is to locate the small release button on the lower backside of the fob. It will be an oval or circular slot. You can open the key fob by pressing the button.

After the key fob has been opened, remove the battery. The new battery should be a CR-2032, and can be purchased online or at a local auto parts store. After you've finished, your key fob should permit you to lock or unlock and start your vehicle even if it's not running.

How do you replace a mechanical key

The Kia keyfob is a wonderful convenience that lets us lock or unlock our car by pressing one button. But, as with all devices it will encounter issues occasionally. Luckily, there are ways to troubleshoot these issues and keep our key fobs in good condition over the long haul.

A dead or weak battery is among the most common issues. This can cause the fob to cease working or stop working at times. If this is the case then replace the battery with a new one.

If this isn't enough to solve the issue, use an ordinary screwdriver with a flat head to wedge the fob's casing made of plastic open. Be careful not damage any internal components, or scratch the plastic. Once the battery is removed and replaced, you can replace it with a brand new battery.

Close and open the door with the mechanical key. (Every kia fob comes with an emergency mechanical key that fits into the slot). Test the key fob to verify that it's working correctly. If the fob isn't functioning, contact a dealer or locksmith to resolve the issue. To avoid locking outs in the future, ensure you have an emergency key that will work in all of the door and trunk cylinders.