UPVC Replacement Door Handles

As time passes the handles on your doors will get worn out and need to be changed. When doing this it is important that the new handles match the exact dimensions of the previous handle.

The top screw's position as well as the lever and keyhole dimensions are the three measurements you need to check. Use the size guide to help with this.

Inline Lever/Lever

A lever/lever handle is a contemporary door handle that is designed to fit new or replacement doors. This type of handle is available in a variety of designs and finishes. This handle is available from a number of manufacturers including Avocet ERA Fullex Hoppe Mila Millenco Yale.

Fab and Fix Windsor Inline Sprung Lever Door Handle

The uPVC/Composite door handles are constructed of durable materials and are suitable for doors with multi-point locks that require a strong design. The handles are inline and work with the same spindle as well as screw fixings. They are easily installed on new or existing uPVC/Composite doors.

The design of the sprung lever allows the handle to be set and angled for comfortable operation and is suitable for all users. The handle has been endurance-tested to 200 000 cycles. This helps ensure that the quality of finish and performance over time. The sprung lever is also adjustable to fit a wide range of locks. This is particularly beneficial for doors with narrower frames, in which the cylinder is further back. A lever that is shorter is an excellent option for doors where the latch could be activated by the thumb turn inside.

Lever Pad

The lever pad upvc handle is distinct from the lever handles that are used on the majority of doors. These handles can operate from a single spindle (inline) or independently from both sides using two offset spindles or inline (pad). They are generally employed on replace upvc window handle double glazed handles-glazed doors and are available in a variety of variations and finishes.

The handles have been tested to a minimum of 200k cycles and are available in various finishes including White, Silver, Chrome & Gold. The finish is BS EN 1670 Grade 5 and is resistant to corrosion. This gives the handle an outstanding performance and durability to serve its intended purpose.

All UPVC handle lever pads come with a spindle, screws, and can be fitted on the uPVC door. The backplate fixation centers of 211mm permit a larger handle, which is usually beneficial when replacing a damaged or old multi-point door lock mechanism. These handle levers have springs, which eliminate the problem of door handles that move out of their horizontal position when not in use.

It is important to match up the PZ dimensions of both the multipoint lock as well as the uPVC doors when selecting a replacement UPVC spindle and handle. This measurement is often referred to as the 'handle centre' or 'cylinder centres' and is a critical aspect in ensuring that you have the right handles.

Once you have decided on the proper PZ size and the correct PZ size, you must ensure that the lever and push pads are designed to fit the American with Disabilities Act compliant handles you require for your door. They are typically round or square, with an internal lever and an external push pad.

The majority of UPVC Lever Pads that we sell are sprung. This means they will return to a horizontal state when not in use instead of hanging and possibly being stuck in the frame. This prevents drafts and cold air from entering a home. The majority of UPVC lever pad handles are available in left and right handed versions, allowing them to be installed on either side of the doors.

Euro Cylinder

Cylinder locks are usually used on uPVC doors, but can also be used on other types of doors. Cylinder locks are operated by using a key that unlocks the cylinder case. This exposes pins that can be aligned with those inside the lock, allowing them to turn the revolving camera, thereby opening the door. Euro Cylinders are available with up to six pins. Doors that are internal and external require different levels of security.

The selection of a cylinder is crucial. It depends on the type of use your doors and handles receive. For instance, exterior doors should be fitted with a more secure cylinder while internal doors can be secured using the standard cylinder. Some cylinders have extra features that can increase security, for instance, anti drill or anti bump properties.

A euro cylinder must be measured correctly to ensure it's the correct size for your door. The cylinder should be measured from the hole in the center of the fixing screw to the end of the cylinder and the thumb turn if you have one. If you are unable measure it using the lock in its position, you can remove it. It is essential to not have a cylinder that extends beyond the handle or escutcheon. This could make it vulnerable to snapping lock attacks.

The majority of modern cylinders have been made with bump and anti-drill features included in their design. They are designed to decrease attack chances by forcing the cylinders to rotate in a different direction. This can to deflect an attack and protect your door.

Certain cylinders are made to resist snapping. This is an increasingly common kind of attack on cylinders, which is where the break line of the lock is smashed by a tool that is specially designed to snap off the front of the cylinder to allow the door to be opened. This is faster and easier to achieve than opening multipoint locks and leaves no evidence of a break-in, which could hinder an insurance claim.

Spring Cassette

This spring cassette is found in the base plate of your door handle. It provides a sprung solution to return the multipoint lock handles to their normal position after usage. In the past, a lot of these types of handle did not have a spring integrated into them and without this they can droop or drop once the locking mechanism is removed. This simple component is the most effective way to solve this issue. It also helps prevent your door from becoming stuck in the closed or open position since they aren't easy to close manually.

These spring cassettes are specifically designed to be used with sprung multipoint locks, they will not fit non-sprung multipoint handles. You will need to have a custom hole cut into the backplate to allow them to fit (please check the image for a technical diagram). These cassettes can be used as a replacement to broken or missing cassettes in the backplate of uPVC victorian door handle handles. They are available as one unit. They come with a square cut out that accommodates an 8mm shaft.

These spring cassettes are a great cost-effective solution to the issue of door handles that are that are sagging. They are simple to put in and will prolong the lifespan of your uPVC doors. Contact us to learn more about our range of uPVC accessories and spares. We are always ready to provide expert advice and to assist you.