Fiat 500 Replacement Key Fob

If your remote key fob has stopped functioning, it could be time to replace the battery. However, if you replace the battery but it is still not working the issue may be elsewhere.

United Locksmith specializes in the production of new keys for classic vehicles. We have all the tools and components needed to provide this service.

Dead Coin Battery

The most frequent reason that your Fiat 500 key fob will not lock or unlock the doors is due to a dead battery. The key fob is equipped with an internal battery called a coin cell which will quickly drain if it is not frequented enough. If your remote has started to show signs of a loss of range or stopped working in the middle of the night, then your battery may be dead.

Metal clips hold the battery in place on the key fob. If the clips aren't tight, they can create contact issues that prevent your remote to receive power. Make use of a flathead screwdriver to open the retaining clips and remove the old battery. Use a battery that has the same voltage, size, and specifications as the original.

The key fob might also become corroded or damaged due to exposure to water. Even a short bath in soapy water may cause damage to the electronic chip inside. It's best to keep your key fob in a dry location.

Water Damage

Water damage may be the reason for your key fob not working properly. The rubber seals on key fobs keep them from being damaged by a light drizzle or splash of water. However, it is crucial to keep the keys of your car away from the washing machine, ocean, and pool.

The key fob is equipped with an electronic chip that sends an immobilizer system of your car. The chip is what allows the 500 to be locked keys in fiat 500 and started. If it gets wet, however it will cease to work.

If you want to check whether your key fob still working, you can clean the internal electronics with isopropyl or electronic cleaner. It is recommended to replace a key fob if it's submerged into salt water rather than attempting to fix it yourself.

While a replacement fob can cost you a bit of money, it is a lot cheaper than paying for your spare fiat 500 key 500 to be towed to the dealership and repaired! You can also do it yourself by following just a few steps. Just ensure you have the right battery type before you attempt to open your key fob. This task is much easier than it looks, and you can find step-by-step instructions online for virtually any key fob for cars.

Faulty Chip

The chip located within the key fob communicates with the vehicle's immobiliser to ensure that the car is capable of starting when the correct key is used. If the chip is damaged or damaged in any way, your car will not start.

A faulty chip can occur due to a variety of reasons but most commonly due to water damage or the battery being dead. It is recommended to leave the task to a professional locksmith who can repair the chip in a short time and at a reasonable cost.

If your key fob ceases to function after exposure to clean water from the tap or rain, unplug the battery and clean the electronic component using a paper towel to ensure that it is completely dry before putting it back in. If the key fob does not work it's most likely to be a damaged chip that must be replaced.

Some people will visit their dealer if they need a new fiat punto key replacement fob. But, this can be expensive. If you are looking for a low-cost solution to have your fiat key programming key fob repaired make sure you contact United Locksmith. We have the equipment and know-how necessary to fix your fiat replacement car keys 500 replacement key cost - read this blog post from Harborhousejeju - key fob in a quick and professional way.

Faulty Receiver Module

Fiat key fobs transmit a signal up 50 feet to the vehicle, which can unlock and lock the doors (and start the vehicle in case of automatic transmissions). However, there are a few things that can cause the fob to cease working. This could be due to a dead battery or water damage, worn-out buttons as well as a receiver issue. signal interference, or a malfunctioning chip.

If the fob was stored in a place that has suffered a severe trauma, such as being dropped on hard floor or getting washed in the washing machine or dishwasher, it might not be capable of communicating with the car's Body Control Module (BCM). This is because the BCM is a secure system that will only accept a signal from a genuine key, and not from any other.

It is necessary to replace the fob if this occurs. A professional locksmith is able to handle all aspects of the key replacement process, including programming a new one for the 500. In fact, they can even provide you with a clone key that functions the same way as your original fob (and costs less than the price).