How to Replace a Kia Sportage replacement kia keys Key

For a variety of Kia models keys, the key has the keyless entry system that is built into the key. This key is similar to an remote control and can be exchanged with an Kia dealer.

Key fobs can stop working due to a variety of reasons, including the battery of the coin is dead worn buttons signals, water damage, signal interference and a damaged receiver module. Here are some tips on how you can get your kia keys made Sportage replacement key back to working.

How do you replace the remote key or the smart key?

Whether your Kia is equipped with an intelligent key, remote key, push-to-start key, or a regular non-transponder metal key the battery in these keys will eventually need replacement key kia. This is particularly when your car displays a message that indicates the smart or remote keys have low battery power.

This is a relatively simple process. In order to replace the battery in the key fob take out the mechanical key from the slit on the back of the key fob. Then pry open the cover. Inside the key fob will be a small screw that holds the battery in place. Utilizing a small screwdriver unscrew the screw and remove the old battery. Install the new battery and close the slit on the key fob.

Once the key fob has new batteries check it by pressing the locks and unlock buttons. If the doors unlock and lock according to your expectations, then you're in good shape! You can now utilize the hands-free feature to lock and unlock your Kia whenever your fingers start to get cold or you need to run errands around Brandon.

Note: Some key fobs (transponder chip or smart keys) may need to have their programming done. This requires a programming machine that is available only to the locksmith for cars or dealer. Other keys (non transponder metal keys) don't require programming. If you're required to reprogramme your key, you'll need note the key code's number on the tag for the key code.

How do I replace a battery

If the Kia key fob does not respond when you press the lock/unlock button, it is likely that the battery is not fully charged. A low battery can also cause other issues, like the check engine light appearing or the engine not running properly. Fortunately replacing the battery on the key fob is a fairly simple DIY task that requires only the most basic tools.

Before beginning the process before beginning the process, ensure that your vehicle is turned off and all doors are closed. Find the small metal or a plastic piece on the bottom of the key fob. Press it until the key pops out. This key can be inserted into the driver door handle to unlock your car.

To replace the battery on the key fob, remove the cover that covers the rear. Use a pry tool to remove the latch that holds the black negative cable. Remove the old battery and align the new battery so that the "+" positive side is facing your face and the "-" negative side is facing towards the fob's metallic electrical contacts. Push the new CR2032 battery straight into place, avoiding excessive force to avoid bending or damaging the metal contacts.

After you have installed the new battery then turn the key fob on and off in the ignition until the door locks cycle. Then you can test your Kia key fob to see whether it's functioning properly again.

How do you replace the smart key?

You can have an ordinary keyfob or Smart Key depending on the model of kia picanto car key Sportage. The smart key has an embedded mechanical key blade unlike the standard key fob, which does not. Both key fobs come with a battery that will eventually require changing. This is a straightforward process that takes just two minutes.

Before you begin it is important to ensure that you're on a level surface with good lighting and that your Kia is turned off. Remember that the fob contains small pieces that could fall if you're not careful.

The small release button is located on the lower backside. This will either be an oval silver button or a rectangular slot. You can open the key fob by pressing the button.

After the key fob has been open, remove the battery that was in it. The new battery should be a CR-2032, and can be purchased online or at a local auto parts store. Once you're done, your key fob should be able to lock the vehicle, unlock it, and then start your vehicle, even if it isn't running.

How do I replace a mechanical key

The Kia key fob is a fantastic feature that lets us lock and unlock our car with the touch of the button. Like all devices like a key fob, the Kia can occasionally have problems. There are ways to resolve these issues and keep your key fobs working for the duration of.

A low or dead battery is one of the most common issues. This can cause your device to stop working or operate intermittently. If this is the case, try replacing the battery with a new one.

If this isn't enough to resolve the issue Try using a standard flathead screwdriver to wedge open the fob's plastic casing. Be careful not to scratch any internal components or scratch the plastic. Once open, carefully remove the battery you have been using and replace it with a brand new one.

When the new battery is in, shut and open the doors using the mechanical key (every Kia Rio 2015 Key fob has an emergency mechanical key that will fit in the slot). Test the key fob to verify that it's functioning correctly. Contact a dealer, or a locksmith to fix the issue when the fob still is not working. Make sure they make you an emergency key that works in all the trunk and door cylinders, to prevent lockouts in the future.