How to Change a Subaru Spare Key

Get a locksmith in touch if you have lost your subaru legacy key key. Usually, they can cut keys for you cheaper than the dealer.

Subaru car keys are typically either smart "push-to-start" fob remote keys or plain metal keys. The Fob key has to have its chip programmed.

Keyless Entry System

The key fob can be used to lock and unlock your Subaru remotely. It can also open the trunk of your car or the lift gate. These remotes work with the keypad in your car to communicate with the computer system inside the vehicle.

Some models of Subaru come with a lesser-known feature called PIN Code Access. You can use a customized number sequence to start and open your vehicle. If you own a newer Subaru Forester, Outback, Crosstrek, WRX, WRX STI, or Impreza that has this feature, refer to your owner's guide to find out how to program subaru key - click the following document - to make use of it.

If your keys stop working, there's a good chance that the battery in the key fob is dying. The first thing you'll want to do is ensure that the battery is in good condition and you can accomplish this with a small remote tester or a basic multimeter in your garage at home.

The next step is to take the circuit board of the transmitter from the key fob to examine it. You'll see one or two sets of eight-digit numbers. Note down the first so you remember it. After you've done this, you can begin programming your key fob at home. The procedure for programming is different based on the model and year of your vehicle, but it's usually simple enough to complete yourself.

Key Fobs

subaru key replacement cost's latest models come with key fobs which not only unlock doors but also turn on lights, lock the gas cap and even start the car. That last trick is especially helpful if you've been at the gas station only to discover that your car won't start because the battery of the key fob died.

No matter if your Subaru is new or older it's likely that your key fob can be replaced without difficulty. Be aware that some most modern models, with their high level technology, may require a visit to the dealer. However, with a little time and effort, you'll have your replacement key subaru fob to use at home.

Begin by opening the case and looking at the circuit board of the transmitter. (Instructions on opening the case are usually included in the owner's manual). It should contain one or two sets of serial numbers, each one of which is 8 digits long. Write down the initial number series and keep it in your wallet to refer to later.

Then, get into the driver's seat. Close all doors. Turn the key ten times to start your car, then switch off the engine. Press the lock button on your key fob and then open the door to ensure that all of your doors are functioning properly. Close the door, and then take the key off. The chime should be heard from your vehicle, signalling that the key fob has been programmed.

Ignition System

The battery in your key may be dead If your Subaru keys don't work as they should. You can replace the battery for your key fob on your own if you are familiar with the procedure. A replacement battery is not expensive and fairly easy to find. If your keypad doesn't respond to your commands, it may be a problem with it. It's best to visit a dealer to get a spare key. They'll ensure that the key is genuine Subaru key that's covered by warranty. It will also be programmed to your vehicle. This is a lot safer and more convenient than purchasing an aftermarket key from a company on the internet.

The dealer is also able to cut keys for you, provided you provide your VIN number and as evidence of ownership. They'll use this information to program the new key so that it can be recognized by your immobilizer. This procedure is more complicated than cutting a key, and the dealership will usually charge more for this service.

Once the new key has been programmed, you'll be able to switch it to your current key. It will take only five seconds to insert the new key, so make sure to keep your working keys close at the ready. When the security light ceases to flash and you're able to remove the new key and test it to make sure it's working properly.

Battery Replacement

Subaru fobs are very useful because they can turn on the power windows and sunroofs of your vehicle with just one button press. The battery inside your Subaru fob wasn't made to last forever, and will require replacement at some point. This short guide from Capitol Subaru will help you to change the battery yourself.

You'll first need to find the small crack that is the gap between the front and back of your keyfob. With a small flathead screwdriver, you can break the seam open and reveal a small compartment inside that houses the battery. Install the new battery and make sure it's facing in the correct direction. Remove the old one. Once you've assembled everything is in place, you can use your new key fob to lock or unlocking your vehicle.

You should always have a spare set of keys, particularly if the one you have is broken or lost. You can buy a new key at your local dealership or get it cut by locksmiths. It is important to ensure that your key fob is working correctly as soon as you can so that you can safely drive.