Reasons Your fiat multipla key 500 Key Fob Won't Work

A key fob for the Fiat 500 allows you to easily open doors and start your vehicle. There are a myriad of reasons why the fob may stop functioning. This includes a dead coin-battery and water damage, as well as issues with the receiver module, and interference.

This listing is for an new key for fiat 500 replacement Fiat Flip Key Remote that is similar to the Ilco brand. It has to be professionally programmed (click here to search for local locksmiths for your vehicle). It includes lock, unlock, and trunk buttons.

Dead Coin Battery

A dead battery is probably the most common cause of your 500 key fob that isn't working. Modern key fobs have limited operating range and must be within a few inches of your vehicle to function. If you're far from your vehicle, and you hit the keyfob, it will not respond and display the message "Key Fob Not Detected".

If this happens you need to replace the battery of your coin-cell (Part Number CR2032) by a new one of a trusted brand such as Panasonic Duracell or Energizer. They are usually available in your local hardware store, or online.

You can test the battery on your coin-cell by pressing the buttons while standing near your fiat 500x key not detected panda key fob replacement [read this blog article from willysforsale.com] 500. The car will blink its parking lights and the key fob should work the lock and unlock switches.

If your fob's key isn't working even after replacing the battery, it might be water damage that prevents it from interacting with the module inside your vehicle. Water damage can occur in many ways, such as an easy splash or submerging the key fob in saltwater at the beach. If you suspect that your fob was exposed to water, put it in a bag of rice to draw out the moisture. If this doesn't work your fob may need to be reprogrammed by a professional auto locksmith or dealer.

Water Damage

Water damage can occur when you immerse the fob into the ocean, or wash it in a washer. Saltwater can cause the circuit board to short, and eventually end up dying. Getting the fob wet is not a good idea however, if you drop it into a glass of water or fail to remove it from your pants pocket prior to running the washing machine, don't give up hope.

First remove the battery from the fob. Clean the electronic chip with isopropyl alcohol or a similar product and then dry it thoroughly before replacing the battery. Check the fob again to verify if it's functioning. If the key doesn't work, it may have to be programmed again. This is usually done by an auto locksmith or dealer.

If the key is newer and was not programmed to your vehicle, it will likely need to be replaced completely. This is an easy process that can be completed by a professional automotive locksmith. The locksmith will require the key cut to match the car's ignition. The locksmith will also have to program your fob into the vehicle's system. This is a cheap and quick process that can be completed locked keys in car boot fiat punto the same day.

Receiver Module Issues

Your 500 key fob may not function because it's out of range. The remote has a range of 30 feet. So when you're too far from your vehicle it won't be able to respond to your commands. This can easily be resolved by moving it closer to your vehicle until it begins responding.

If you've replaced your coin battery (commonly called"button" or "button" or "watch") and the fob won't work It could be because of an internal circuit board issue. In most cases, reprogramming the fob can resolve the issue. You can find the instructions on how to do this for the majority of automobiles by searching YouTube or consulting the owner's manual.

It is possible to replace the metal clips that hold the battery of your coin in place. If they loose tension, it could prevent the coin battery from being properly seated and result in the malfunction of your remote.

In rare instances, the fob may become desync'd with your vehicle because of software or hardware issues. This could be a huge problem, but you can usually fix it by visiting a local dealer or auto locksmith to reprogram your fob for you. In some cases they may have to reinstall the software on your body control module too.

Interference

Interference can also cause the key fob to be unable to receive or transmit a signal. This can happen when the key fob is close to an electronic radio transmitter (cell phones and radar detectors) or another source of electromagnetic radiation. Other reasons why the key fob may not function may be a lack of connection to the buttons or the internal chip or water damage.

If your key fob suddenly stopped working, or if you've tried everything at home to fix it (e.g. battery replacement, reprogramming and using the spare key fob, you could have a damaged receiver module on your 500. The receiver module, which is located under the dashboard, receives radio frequency signals from your key fob. It converts the signals into electronic commands that are then translated by the vehicle.

There is a straightforward method to reset the 500's in-board system, including the keyfob. Disconnect the battery for 15 minutes, removing first the negative cable and then the positive cable. Reconnect the battery. This will eliminate any remaining electricity, and allow you to restart the car's computer. This will help you get your key fob to work again. If the issue continues you should speak with an experienced technician. They can determine the exact cause of your problem.