Reasons Your spare fiat 500 key 500 Key Fob Won't Work

A key fob with the fiat 500x key fob 500 number is a convenient way to unlock the doors and get started the car. However, there are numerous reasons why the fob won't be working. These include a dead coin battery water damage, receiver module problems, and interference.

This listing is for an NEW replacement fiat replacement car keys Flip Key Remote that is similar to the Ilco brand. It needs to be professionally programmed (click here to find local locksmiths in the automotive industry). It comes with lock, unlock and trunk buttons.

Dead Coin Battery

The most frequent reason that the 500 key fob won't function is due to an inactive battery. Modern Key Fiat fobs have a limited operating range, and should be within a few feet of the vehicle in order to function. If you're not close to your vehicle when you press the key fob button the car won't respond, and will display an "Key Fob Not Detected" message in the instrument cluster.

If this happens, replace the battery on your coin cell (Part number CR2032) with a fresh one from a reliable brand such as Panasonic, Duracell, or Energizer. You can usually find them in your local hardware store or online.

After you've changed the battery on the coin cell you can test it by standing close to your fiat key duplication 500 and pressing the buttons. The parking lights should blink and the key fob should operate the lock and unlock switch.

If your key fob still isn't working after replacing the battery, it may be water damage that hinders it from interacting with the module inside your vehicle. Water damage can occur through a variety of methods, including the simple splash or submerging the key fob saltwater at the beach. If you suspect your fob was exposed to water, try placing it in a dry rice bag to pull the moisture out. If this doesn't work, you will require your fob to be reset by an auto locksmith or dealer.

Water Damage

While the fob comes with rubber seals to keep water from the electronic chip inside and out of the ocean or washing it in a machine can cause water damage. Saltwater can cause the circuit board to short, and eventually die. It's not the best idea to get the fob wet, but don't give it up even if you accidentally drop the fob in water or forget to take it out of your pants pocket.

First take the battery off the fob. Before replacing the battery clean the electronic chip with isopropyl or a similar product. Then try the fob and test if it works. If the key does not function, it may have to be programmed again. This is usually done by an auto locksmith or dealer.

If the key is older and has never been programmed to your car It is likely that it needs to be replaced completely. A professional locksmith in the automotive industry can do this job. The locksmith must cut the key to match the ignition in your vehicle. They'll also need to reprogram the fob for the system of your car. This is a simple and cost-effective procedure that can be completed in the same day.

Receiver Module Issues

One of the main reasons why your 500 key fob might stop functioning is because it's out of range. The remote typically has 30 feet of range or less, and if it's too far from your vehicle, it will not respond to your commands. This can be fixed by moving closer to your vehicle until it begins responding.

If you've replaced the battery in your coin (commonly known as"button" or "button" or "watch") and the fob isn't working It could be because of an internal circuit board problem. Reprogramming the fob typically resolves this issue. You can find the instructions on how to get fiat key code to do this for all automobiles by searching YouTube or reading the owner's manual.

It is sometimes necessary to replace the clips made of metal that hold the coin batteries in the correct position. If they loose tension, they could stop the battery from being seated properly and can cause the remote to malfunction.

In rare instances, the fob may become disconnected from your vehicle because of software or hardware issues. This can be a major trouble, but you could usually fix it by visiting an auto locksmith to reprogram your fob. In some instances they may have to install the software again in your body control module, too.

Interference

In addition to a dead coin battery The key fob may not be able to transmit or receive signals due to interference. This is possible when the key fob is located near an electronic radio transmitter (cell phones, radar detectors) or another source of electromagnetic radiation. Other reasons why the key fob could not function include a poor connection to the buttons or damage to the internal chip or water damage.

If the key fob has failed to work one day in the middle of the night or even after trying every option at home to resolve it e.g. You might have a damaged 500 receiver module if you've tried replacing the battery, reprogramming or using an alternative key fob. The receiver module is located under the dash and is able to pick up the radio frequency signals from the key fob. It converts the signals into electronic commands, which are then read by the vehicle.

There's a simple method to reset the 500's onboard system, including the keyfob. Disconnect the battery for 15 minutes, removing first the negative cable and then the positive cable. Then reconnect the battery. This will clear out any remaining electricity and restart the car's computers. This can help you get your key fob working again. If the problem persists you should seek the advice of an expert technician. They can identify the root cause of any problems.