How to Replace a Kia Sportage Replacement Key

For a variety of Kia models, the key contains a built-in keyless entry system. This key is similar to a remote control and is exchangeable by a Kia dealer.

Key fobs might stop working due to a number of reasons, including the battery being dead, worn-out buttons, signal interference or water damage. Here are some tips to help you get your Kia key fob that is a replacement for the sportage for good.

How to replace the remote key or smart key?

If your Kia is equipped with an intelligent key, remote key push-to-start key, or a standard non-transponder key made of metal The battery inside these keys will eventually need replacing. This is especially true if your car displays a message telling you that the smart or remote keys are in poor condition.

It's a relatively simple process. In order to replace the key fob battery take the mechanical key from the slit on the back of the key fob. Next, break the cover. A small screw is inside the key fob to keep the battery in its place. Using a small screwdriver, unscrew the screw and remove the old battery. Install the new battery and close the gap on the key fob.

Test the key fob by pressing the lock and unlock buttons. If the doors unlock and lock as expected, then you're all set! You can now use your kia remote key replacement's hands-free lock/unlock feature when your fingers are cold or you need to go on errands around Brandon.

Note: Certain key fobs (transponder chip or smart keys) may need to have their programming completed. This requires a programing machine which is available to the locksmith who works for the automotive dealer. Other keys (non-transponder metal keys) do not require programming. If your key requires to be reprogrammed, then you will need to know the key code number that is stamped on the tag of the key code and record it in a safe place.

How to replace the battery

If the Kia key fob is unable to respond to pressing the lock/unlock button, it is likely that the battery is depleted. A low battery could cause other problems like the check engine light flashing on or a delay in cranking the engine. Fortunately replacing the battery on the key fob is a relatively easy DIY project that requires just the most basic tools.

Make sure to shut off your vehicle and close all doors prior to starting. Find the small metal or plastic piece on the bottom of the key fob. Move it until the metal key comes out. This key can be placed inside the driver door handle to unlock your car.

To replace the key fob's battery, take off the cover from the back and use a plastic pry bar tool to loosen the latch holding the black negative battery cable. Remove the old battery and then orient the new one in a way that the "+" positive side faces your face and the "-" negative side is facing towards the fob's metal electrical contacts. Push the new CR2032 battery straight into place, avoiding excessive force to avoid damaging or bending the contacts of the metal.

Once the new battery has been installed then turn the key fob off and then on in the ignition for a few times until the door locks cycle. You can then test the Kia's key fob to ensure it is working correctly.

How do you replace the smart key?

Depending on the model of the Kia Sportage, you may have a standard key fob or a smart key. The smart key features an embedded mechanical key blade, unlike the standard key fob, which does not. Both types of key fobs are equipped with an internal battery that eventually will need to be replaced. This is a simple procedure that takes only two minutes.

Be sure to turn off your kia picanto smart key and stand on a level well-lit and well-lit area before you begin. Also, remember that there are tiny components inside the fob which could be snagged if not vigilant.

The first step is to find the small release button on the back of the lower part of the fob. This will either be an oval silver button or a rectangular slot. After pressing this button the mechanical key blade will pop out and you will be able to open the key fob.

Once the key fob is opened, remove the battery that was in it. The new battery is a one called CR-2032 and can be purchased from a local or online auto parts shop. Once you're done, you should be able to lock or unlock your car using your key fob, even if the engine isn't running!

How do you replace the mechanical key

The 2010 kia forte key fob programming, https://flexhaja.com, keyfob is a wonderful convenience that lets us lock or unlock our car with just pressing a button. As with all devices like a key fob, the 2015 kia soul key fob can occasionally have problems. There are solutions to address these issues and keep your key fobs working for an extended period of time.

One of the most frequent problems is a low or dead battery. This can cause the fob to stop working entirely or even to stop working intermittently. If this happens then try replacing the battery with a fresh new one.

If this doesn't fix the issue Try using a standard flathead screwdriver to wedge open the fob's plastic casing. Be cautious not to damage any internal components or scratch the plastic. When the battery is open, carefully take off the battery you have been using and replace it with a new one.

After the new battery has been put in, close and open the doors using the mechanical key (every 2016 kia optima key fob programming fob has an emergency mechanical key that will fit into the slot). Test the key fob to ensure that it's working correctly. Contact a dealer or a locksmith to resolve the problem when the fob still is not working. Make sure they cut you an emergency key that can work in all the door and trunk cylinders to prevent lockouts in the future.