Reasons Your fiat multipla key 500 Key Fob Won't Work

A key fob from fiat punto locked keys in car 500 is a convenient method to unlock the doors and get started the car. There are a myriad of reasons the key fob might stop working. This could be due to a dead coin-battery and water damage, as well as problems with receiver modules, as well as interference.

This listing is for a NEW replacement fiat replacement car keys Flip Key Remote - an exact replica of the Ilco brand that needs to be professionally programmed by a local automotive locksmith (click here for Locksmith Search). It comes with lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is the main cause of your 500 key fob not working. Key fobs of today have an operating range that is limited and must be within a few inches of the vehicle to work. If you're far from your car and push the keyfob button it won't respond and display the message "Key Fob Not Detected".

If this occurs If this happens, replace the battery in the coin-cell (Part Number CR2032) by a brand new one of a reputable brand such as Panasonic Duracell or Energizer. You can find them at the local hardware store or online.

You can test the battery in the coin-cell by pressing the buttons while standing near your fiat 500 car key replacement 500. The car will flash its parking lights and the key fob should work the lock and unlock switches.

If the key fob doesn't function after replacing the battery, it may be damaged by water that blocks it from communicating with the receiver module in your vehicle. Water damage can occur in a number of ways, ranging from the slightest splash to submerging the fob in salt water at the beach. If you suspect your fob has been exposed to water, try putting it in a dry rice bag to pull the moisture back out. If this fails, you'll require your fob to be reprogrammed either by an auto locksmith or dealer.

Water Damage

While the fob has some rubber seals to keep water out of the chip's electronic circuit and out of the ocean or washing it in a machine can cause water damage. Saltwater can be particularly harmful to the circuit board of the fob which causes it to short out and eventually die. It's not the best idea to submerge the fob in water, but don't give it up when you accidentally drop it in water or fail to remove it from your pants pocket.

First, remove the battery from the fob. Before replacing the battery, clean the electronic chip using isopropyl or a similar product. Next check the fob to see if it works. If the fob doesn't work it could need to be reset. This is usually done by an auto locksmith or dealer.

If the key is a newer model and was not programmed to your vehicle it is likely to need to be replaced completely. This is a simple procedure that can be handled by a professional automotive locksmith. The locksmith needs to cut the key to match the ignition in your vehicle. They'll also have to reprogram the fob to your vehicle's system. This is a low-cost and fast process that can be completed the same day.

Receiver Module Issues

One of the most common reasons why your 500 key fob might stop functioning is that it's out of range. The remote typically has an operating range of 30 feet or less, and if it's too far away from your car it won't respond to your commands. It can be solved by moving closer to your vehicle until it starts responding.

If your fob isn't working after replacing the battery in the coin, also called a "button", "watch" or "button", it may be due to a malfunction on the internal circuit board. Locked Keys In Car Boot Fiat Punto most cases, reprogramming the fob can resolve the problem. You can find the instructions for most vehicles on YouTube or in the owner's guide.

You may need to replace the metal clips that hold the battery of your coin in place. If they lose tension, it can stop your coin battery from being properly seated and cause your remote to malfunction.

In rare instances the fob might become desync'd with your vehicle because of software or hardware issues. This could be a huge trouble, but you could usually fix it by visiting an auto locksmith to reprogram your fob. In certain instances, the software may also require reinstallation in your body control modules.

Interference

In addition to a dead battery on a coin The key fob might not be able to transmit or receive the signal due to interference. This is possible when the key fob is near an electronic radio transmitter (cell phones or radar detectors) or another source of electromagnetic radiation. Other reasons the key fob may not function include a weak connection to the buttons or damage to the internal chip or water damage.

If your key fob suddenly stopped working, or if you have tried everything at home to solve the issue (e.g. You may have a faulty 500 receiver module if you've tried replacing the battery, reprogramming, and using a spare key fob. The receiver module, located beneath the dashboard, picks up radio frequency signals from your key fob. It converts the signals into electronic commands which are then translated by the vehicle.

Luckily, there is an easy way to reset all on-board systems in your fiat 500 remote key programming device, including the key fob. Disconnect the battery for 15 minutes by removing first the negative cable and then the positive cable. Then reconnect the battery. This will eliminate any remaining electrical charge and restart the car's computers. This could help get your key fob working again. If the problem persists you should speak with an expert technician. They'll be able to identify the root cause of your problems.