Reasons Your Fiat 500 Key Fob Won't Work

A key fob for fiat punto key replacement 500 makes it simple to open doors and start your car. However, there are numerous reasons why the fob won't be working. These include a dead battery damage to the receiver module, issues, and interference.

This listing is for a NEW replacement fiat replacement key cost Flip Key Remote that is similar to the Ilco brand. It needs to be professionally programmed (click here to find local locksmiths in the automotive industry). It comes with lock, unlock and trunk buttons.

Dead Coin Battery

The most common reason the 500 key fob won't function is due to a dead battery. Modern key fobs operate with a limited range of operation, and must be within a few feet of the vehicle to operate. If you're far from your vehicle, and you hit the keyfob, it won't respond and display the message "Key Fob Not Detected".

If this happens, simply replace the battery in the coin cell (Part number CR2032) with a brand new one from a reputable brand such as Panasonic, Duracell, or Energizer. They are usually available at your local hardware store or on the internet.

After you've replaced the battery of your coin cell, you can test it by standing next to your fiat key cutting - spectr-sb116.ru - 500 and pressing the buttons. The parking lights should flash and the key fob should operate the lock and unlock switch.

If the fob's remote doesn't function after replacing the battery, it may have water damage that stops it from connecting to the receiver module inside your vehicle. Water damage can happen in a number of ways, from small splashes to submerging the fob salt water at the beach. If you suspect your fob has been exposed to water, try putting it in a dry rice bag to pull the moisture back out. If this doesn't work, your fob will probably need to be reprogrammed by an experienced locksmith or dealer.

Water Damage

Water damage can occur if you immerse the fob into the ocean or wash it in a washer. Saltwater can be particularly harmful to the circuit board of the fob that can cause it to short out and eventually end up dying. The fob getting wet is not a good idea, but if you drop it in the water in a cup or forget to take it out of your pants pocket before running the washing machine, don't give up hope.

First, remove the battery. Before replacing the battery clean the electronic chip using isopropyl or similar products. Then, test the fob to see if it works. If the fob doesn't work, it may have to be changed. This is typically handled by a dealer or professional auto locksmith.

If the key is a newer model and has never been programmed to your vehicle It is likely that it needs to be replaced completely. This is a simple process that can be completed by a professional locksmith for automotive use. The locksmith needs to cut the key to match the ignition of your car. The locksmith also needs to reprogram your fob into the car's system. This is a cost-effective and quick process that could be completed the same day.

Receiver Module Issues

The 500 key fob could stop working because it is out of range. The remote usually has an area of 30 feet or less and if it's far from your car, it will not respond to your commands. You can easily fix this by moving the remote closer to your car until it responds.

If you've replaced your coin battery (commonly known as a "button" or "watch") and the fob isn't working it could be due to an internal circuit board issue. In the majority of cases, reprogramming your fob can resolve the issue. You can find the instructions on how to do this for most vehicles by searching YouTube or reading the owner's manual.

It is sometimes necessary to replace the clips made of metal that hold the coin batteries in place. If they lose tension it can stop your coin battery from being properly seated and cause your remote to malfunction.

In rare cases the fob could be desync'd with your vehicle due to software problems or hardware issues. You can fix this problem by visiting your local auto-locksmith or dealer to reprogram your key fob. In some instances, the software may also require reinstallation to your body control modules.

Interference

In addition to a dead coin battery The key fob might not be able to transmit or receive an signal due to interference. This could occur if the key fob is in close proximity to a radio transmitter, like a cell phone or radar detector. Other reasons why the key fob might not work include a weak connection to the buttons or damage to the internal chip, or water damage.

If your key fob suddenly stopped working, or if you have tried everything at home to resolve it (e.g. battery replacement, reprogramming and using the spare key fob, it could have a faulty receiver module on your 500. The receiver module is located under the dash, and it picks up the radio frequency signals from the key fob. It converts them into electronic commands that the vehicle interprets.

Fortunately, there's an easy way to reset every single system on board in your 500 and include the key fob. Disconnect the battery for 15 minutes, removing first the negative cable, then the positive cable. Then, reconnect the battery. This will remove any residual electricity and restart the car's computer system, which can help the key fob to function again. If the issue persists, you should speak with an expert technician. They can identify the exact cause of problems.