Repairs to uPVC Windows

uPVC is a fantastic choice for modern homes. They are easy to maintain and durable, as well as long-lasting. In contrast to aluminium and timber, they don't get rusty or decay.

Regularly cleaning and lubricating UPVC windows and doors is crucial. This will reduce repair costs as well as increase energy efficiency.

1. Broken Glass

The broken glass in your windows could cause severe damage to your home and may even be fatal. It is important to take the time to ensure that you're doing all you can to ensure that your windows are in good condition.

For single pane windows, it is relatively easy to replace them, and the replacement will generally fit within the frame that was previously installed easily. If windows with double panes are joined by internal beading, it is more difficult to remove and replace the panes that were previously in use. In this situation, you will need to source some plastic spacers to assist the new pane to fit properly into the frame of the window.

If you're planning attempt to remove the glass panes yourself, it is essential to wear the appropriate safety equipment such as gloves that are thick and protective eyewear. It is also recommended to lay down a dropcloth before you begin working on the window panes so that any shards fall onto the fabric and not on the floor and could be trampled under.

Once the glass is removed from the window, it's best to seal the gap with clear packaging tape or duct tape to block drafts and water from entering the home until a professional is able to come out and repair the window. This will also provide a barrier to prevent any intruders from making their way into your home. If the gap between the window and the door is large, you might want to use security screens that includes a window repairs. This will provide the best of both.

2. Sagging

uPVC windows and doors are a low-cost, durable and energy-efficient alternative to timber sash windows. Over time, they can develop a number of problems that include sliding. A sagging uPVC window can cause issues with light, draughts, and even security. It is crucial to act as soon as you discover that your uPVC windows are sagging.

To repair a window that is sagging, you can try repositioning the hinges. You'll first need to open the windows so you can get at the frame. Then, remove both the top and bottom hinges with a screwdriver and adjust them clockwise or counter-clockwise. Close your window to test the fit after having relocated your hinges. If you're satisfied with the fit, tighten the screws to ensure that they remain in the right place.

If you are unable to reposition the hinges, you might have to replace the seal. Rubber seals can dry out and lose their elasticity with time, which causes them to loosen. It is important to replace your seal as quickly as you can to keep your uPVC window waterproof and draughtproof.

uPVC handles may also become loose. The majority of the time this is due to screws that have come loose over time. However, it could be due to the fact that the handle mechanism has worn out. Fortunately, it's easy to fix the loose uPVC window handle yourself. First, you'll need to close the window and then perform an experiment fit. The corners of the sash should be aligned with the casing joint. If it doesn't then you can use a screwdriver or a wrench to loosen the handle, and then turn the mechanism back into position.

3. Water Leaks

If you wake up to wet floors and damp walls every time it rains it's crucial to take action. Windows that leak water do can not only cause destruction of your home's structure but also undermine your efforts to control the temperature in your home. Most of the time, uPVC window leaks are caused by damaged or missing sealant.

It is a fairly easy fix and should be undertaken by any DIY expert. Based on the severity of the issue the caulking that was used up may require removal before a fresh layer is applied. It is important to remember that when it comes to uPVC window repairs, you should avoid the temptation to "over-caulk' as this will only make the area more difficult to clean and can reduce your energy efficiency.

Check that any drainage holes do not have debris in them and that the sill pan has been properly angled to allow the water to drain from the window. In more extreme instances, you may need to replace the window.

Other indicators of long-term water leakage are decayed sills and the appearance of black spots of mold on the wall near the window. The mold thrives in damp environments and can quickly spread throughout the home.

It is also important to keep in mind that if the leak originates from the glass in your double glazed windows, it is more likely to be a problem with the glass seal, rather than the frame or sagging. A uPVC specialist can easily solve this issue by replacing the glass seal. This will restore the full insulation of your windows.

4. Faulty Hinges

Hinges could be at fault when your uPVC window is difficult to open, or if it opens with the breeze. Anyone with the skills to fix them can replace these in a matter of minutes.

Almost every household in the UK will have either top hung or side-hung uPVC windows that have hinges and, just like any mechanical component they are susceptible to wear and tear over time. The process of replacing a hinge on a window is essentially a very simple procedure, but it is easier to do if you have someone to assist in holding the frame in place.

Verify that the upvc window repair hinges open and close in the correct direction. You can check this by looking for the arrows on each hinge. This indicates the direction in which the window should open.

Window hinges that aren't working properly can be caused by incorrectly opening the window in a certain way or due to inadequate installation at the factory. It is usually possible to fix the issue by sending us a photograph through our website and we will be pleased to offer you suggestions.

It is also crucial to ensure that the hinges are lubricated regularly. This can be accomplished by applying a light engineering oil on the hinges, we recommend using a solvent-free lubricant such as the 3-in-one Multi-Purpose oil. Regular lubrication can help the window open and close more easily. It can also reduce the possibility of a window getting stuck and stop corrosion. It is recommended to do this at least once a year. WD40 or other solvent-based lubricants should not be used since they can damage your uPVC windows.

5. Draughts

Draughts in Upvc windows can be caused by a variety of different things. Firstly the hinges, again because of wear and tear, can become misaligned, this causes a gap to form where the sash meets the frame. If they are beyond repair, it may be necessary to have them realigned. The second is the interlock, which is located on the hinge of the window repair and can also become misaligned, again it is possible to give them a good clean, but in some instances it could be necessary to have these replaced.

The seals may wear out or be damaged over time, allowing air to escape. This can be avoided by replacing them with high-quality weatherstripping. Replace the windows made of upvc with low-emissivity glass. This will help control indoor temperatures and lessen the possibility of draughts.

One of the most effective methods to reduce the draughts in your home is to use a draught excluder, these are typically fabric tubes which are filled with a type of filler. They can be positioned on top of your windowsill. They can keep your home warm by blocking out cold air.

The windows made of upvc can continue to provide excellent insulation and security for your home with a little regular maintenance and repairs. It is important to remember that all windows will eventually become worn out, and it is more cost-effective to simply replace them than to repair them. If you encounter any issues with your upvc window, it's best to consult an expert as soon as possible.