How to Replace a Kia Sportage Replacement Key

For many Kia models, the key contains a built-in keyless entry system. The key is usually akin to a remote control and can be exchanged by a new one purchased from a Kia dealer or locksmith.

Key fobs can stop working due to various reasons, such as an empty coin battery, worn buttons signals, water damage, signal interference and a damaged receiver module. Here are some suggestions to help you get your Kia sportage replacement key working again.

How to replace the remote key or smart key

It doesn't matter if your kia smart key programming is equipped with an intelligent key, remote key push-to-start keys, or a standard non-transponder key made of metal, the battery in these keys will eventually require replacing. This is especially relevant if your car displays a message indicating that the remote or smart key has low battery power.

Luckily, this is quite simple to do. To replace the battery in the key fob take out the mechanical key from the slit in the back of the key fob. Next, pry open the cover. Inside the key fob there will be a small screw that holds the battery in the correct position. Remove the old battery by removing the screw using a small screwdriver. Install the new battery and then close the gap on the key fob.

Test the key fob by pressing the lock or unlock buttons. If the doors lock and unlock according to your expectations, then you're good to go! You can now make use of your Kia's hands-free lock/unlock feature when your fingers are cold or you have to run some errands in Brandon.

Note: Some key fobs (transponder chip or smart keys) might require their programming completed. This requires a programing machine that is only available to the locksmith who works for the automotive dealer. Other keys (non-transponder metal keys) don't require programming. If you're looking to reprogramme your key, you'll need to record the key code number on the key code tag.

How do you replace the battery?

If the Kia key fob is unable to respond to pressing the lock or unlock button, it's a sign that the battery is not fully charged. A battery that is not functioning properly can cause other issues, such as the check engine light turning on or the engine not cranking properly. It is quite simple to replace key fob batteries with only two tools.

Before starting the process ensure that your vehicle is turned off and that all doors are closed. Locate the small plastic piece that is on the bottom of your key fob, and gently jiggle it until the metal key is released. Then, you can put the key into the driver's door handle to unlock your car.

To replace the battery on the key fob remove the cover on the rear. Make use of a plastic pry tool to loosen up the latch that holds the black negative cable. Remove the old battery and then position the new battery to ensure that its "+" side faces you, and the "-", negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into place without putting too much force on it to avoid bending or damaging the contacts of the metal.

After you have installed the new battery after which you turn the key fob on and off in the ignition until the door locks up. Then you can test your Kia key fob to check whether it's working again.

How do you replace the smart key?

Depending on the model of your 2011 kia soul replacement key Sportage, you may have the standard key fob, or a smart key. The smart key has an embedded mechanical key blade while the standard keyfob does not. Both types of key fobs are equipped with an internal battery that will eventually need to be replaced. It's an easy process that takes only two minutes.

Make sure you turn off your kia rio key, and be on a level, well-lit surface before you begin. Also, remember that there are tiny components inside the fob that can fall out if not careful.

The small release button is located on the lower backside. This will either be an oval silver button or a rectangular slot. You can open the key fob by pressing the button.

After the key fob has been opened, remove the battery that was in it. The new battery is one called CR-2032 and can be bought on the internet or at your local auto parts store. Once you're done, your key fob should be able to lock the vehicle, unlock it, and then start your vehicle even if it's not running.

How do you replace the mechanical key?

The Kia keyfob is a great convenience which allows us to lock or unlock our car key kia with just pressing one button. Like any device it is possible that the kia picanto key programming key fob may have issues. There are ways to address these issues and keep your key fobs functioning for many years.

A dead or drained battery is one of the most frequent problems. The fob could be able to stop working completely or stop working at times. If this happens try replacing the battery with a fresh new one.

If this doesn't resolve the problem you can try using a standard flathead screwdriver and wedge it into the fob's plastic casing. Be careful not to damage any internal components, or scratch the plastic. Once the battery is removed, replace it with a brand new battery.

When the new battery is installed, close and unlock the doors with the mechanical key (every Kia fob comes with an emergency mechanical key that will fit into the slot). Test the key fob to check that it's functioning properly. If the device isn't functioning, contact an authorized locksmith or dealer to help resolve the problem. To avoid a lockout in the future ensure you have an emergency key that can be able to work with all trunk and door cylinders.